MathClicksIGCSE← All notesCambridge IGCSE® Mathematics 0580ExtendedChapter 15 — Scale Drawings, Bearings and Trigonometry
15.2 Bearings
Measuring direction from north, writing bearings in three figures, finding back bearings and solving journey problems on a scale drawing.
What a bearing is
A bearing is how navigators, pilots and examiners describe a direction. Everyday words such as
“north-east” are not precise enough, so a bearing gives the direction as an angle.
Definition
A bearing is an angle that is
(1) measured from the north line,
(2) measured clockwise, and
(3) written with three figures.
All three rules earn marks. A direction of 65 degrees must be written 065°, and
a direction of 8 degrees must be written 008°. Bearings run from
000° all the way round to 360°, so a bearing is never
negative and never more than 360°.
Two bearings, measured the only legal way
Watch out
“The bearing of B from A” means you stand at
A, draw the north line at A, and turn clockwise until you face
B. The order of the letters decides where the north line goes, and swapping them
changes the answer completely.
Example 1Write each of these directions as a three-figure bearing: north, north-east, east, south-east, south, south-west, west, north-west. Also write “a direction of 8 degrees east of north” correctly.
1
Start at north, which is 0°,
and add 45° for each step clockwise round the compass.
N 000° NE 045° E 090° SE 135°
2
Keep going clockwise past south.
S 180° SW 225° W 270° NW 315°
3
For the last part, 8° is
only one figure, so pad it to three with leading zeros.
8° → 008°
N 000° NE 045° E 090° SE 135° S 180° SW 225° W 270° NW 315° · and 008°
Exam tip North can be written 000° or
360°; both are accepted. Everything else must have exactly three figures before
the degree sign.
Reading and drawing a bearing
A protractor only measures up to 180°, so bearings split into two cases.
Bearing less than 180°
Put the protractor centre on the point, the zero line along north, and read the
clockwise scale directly.
Bearing more than 180°
Measure the smaller angle anticlockwise from north instead, then subtract from
360°.
anticlockwise angle = 360° − bearing
Note Some protractors let you measure clockwise past 180° from the south line:
if the angle from south, measured clockwise, is x, then the bearing is
180° + x. Use whichever you find easier — but always sketch the arrow first
so you can see roughly what the answer should be.
Example 2The bearing of Y from X is 250°. Explain how to draw this accurately with a protractor.
1
Mark X and draw a north line
straight up from it. Label it N.
2
250° > 180°, so a
single protractor reading clockwise is impossible. Work out the anticlockwise angle instead.
360 − 250 = 110°
3
Place the protractor centre on
X with its zero line along the north line, and measure
110°anticlockwise. Mark the point and draw the ray
XY.
4
Sanity check the picture:
250° lies between 180° (south) and
270° (west), so the arrow must point into the south-west quarter. It does.
Measure 110° anticlockwise from north at X
Bearings compass
Drag the slider (or type a value) and watch the arrow turn. The dashed arrow is the back
bearing, and the working is written out underneath.
bearing065°
Back bearings
If you know the bearing of B from A, the bearing of
A from B is called the back bearing. It is the direction
of the return journey.
The rule
back bearing = bearing + 180° (if the bearing is less than 180°)
back bearing = bearing − 180° (if the bearing is 180° or more)
Choose whichever keeps the answer between 000° and 360°
Why the rule works
North lines are parallel, and the line joining the two points is a transversal across them.
The angle at A between north and AB, and the angle at
B between north and BA, are co-interior (allied) angles,
so they add up to 180°.
Two parallel north lines and one transversal
Exam tip If a question says “give a reason”, the reason is
co-interior angles between parallel lines add to 180° (some books call them allied angles). Naming
the angle fact is worth a mark on its own.
Example 3(a) The bearing of B from A is 062°. Find the bearing of A from B. (b) The bearing of Q from P is 205°. Find the bearing of P from Q.
1
(a) 062° is less than
180°, so add180°.
62 + 180 = 242°
2
Check with the diagram: B is
north-east of A, so A must be south-west of
B. 242° is south-west. ✓
3
(b) 205° is more than
180°, so subtract180° — adding would
give 385°, which is not a bearing.
205 − 180 = 25° → 025°
(a) 242° (b) 025°
Watch out Do not forget the third figure. Writing “25°” instead of
“025°” can cost the accuracy mark.
Example 4The bearing of B from A is 118°. Use the north lines to find the bearing of A from B, giving a reason for each step.
Use the diagram of the two parallel north lines above.
1
The north lines at A and
B are parallel, and AB is a transversal. So the angle at
A and the angle at B marked on the diagram are
co-interior angles and add to 180°.
angle NAB = 118°
2
So the angle at B between its
north line and BA is
180 − 118 = 62°
3
A lies to the west of
B, so from north at B you must turn clockwise nearly all the
way round.
360 − 62 = 298°
4
Confirm with the shortcut:
118 < 180, so add 180°.
118 + 180 = 298° ✓
bearing of A from B = 298°
Why both methods agree The co-interior angle gives
180 − b on the other side of the north line, and going clockwise
the long way round gives 360 − (180 − b) = 180 + b. That is the
+180° rule.
Bearings on a scale drawing
Most bearing questions are really journey questions: go so far on one bearing, then so far on another,
and describe where you end up. On Paper 4 you may be told to answer by accurate drawing.
The method
Choose a scale and write it down, for example 1 cm represents 1 km.
Mark the starting point and draw a north line at it.
Measure the first bearing clockwise from that north line and draw the leg to the correct length.
Draw a new north line at the next point — this is the step candidates forget — and
repeat for the second bearing.
Join the start to the finish, measure that length with a ruler and its bearing with a protractor, then
convert the length back using the scale.
Example 5A walker leaves village V, walks 5 km on a bearing of 048° to W, then 7 km on a bearing of 155° to X. Using a scale of 1 cm to 1 km, find the distance and the bearing of X from V.
1
Choose the scale and convert the two distances.
1 cm to 1 km, so VW = 5 cm and WX = 7 cm
2
Draw a north line at V, measure
048° clockwise from it and draw VW = 5 cm.
3
Draw a new north line at
W (parallel to the first), measure 155° clockwise from it
and draw WX = 7 cm.
4
Join VX, measure it, and convert
back with the scale.
VX = 7.3 cm → 7.3 km
5
Measure the bearing of X from
V clockwise from the north line at V.
bearing = 114°
VX ≈ 7.3 km on a bearing of 114°
Exam tip The same journey can be calculated. The angle at
W is (048 + 180) − 155 = 73°, so the cosine rule
gives VX² = 5² + 7² − 2(5)(7)cos73° = 53.5, giving
VX = 7.32 km. Calculated answers are exact; measured answers are accepted within
about ±0.1 cm and ±2°.
Where this goes next When a bearing question says “calculate” rather than
“by accurate drawing”, you need the tools of the rest of this chapter:
Pythagoras and SOHCAHTOA when a right angle appears (very common, because bearings that differ
by 90° give one), and the sine rule or cosine rule when it does not.
The bearings work is identical — you still find the angle inside the triangle first.
More worked examples
Example 6From a point A, the bearing of B is 072° and the bearing of C is 145°. Given that AB = AC, find (a) angle BAC, (b) angle ABC, (c) the bearing of C from B.
1
(a) Both bearings are measured from the same
north line at A, so subtract them.
angle BAC = 145 − 72 = 73°
2
(b) AB = AC, so triangle
ABC is isosceles and the two base angles are equal.
angle ABC = (180 − 73) ÷ 2 = 53.5°
3
(c) Start from the direction you already know at
B: the back bearing of A.
bearing of A from B = 72 + 180 = 252°
4
Turning from BA to
BC is a turn of 53.5°. Adding would give
305.5°, which points north-west; but the diagram shows
C is south of B, so subtract.
252 − 53.5 = 198.5°
(a) 73° · (b) 53.5° · (c) 198.5°
Watch out Adding or subtracting the triangle angle is decided by the
diagram, never by habit. Always sketch first and ask which quarter of the compass the answer should
be in.
Example 7A ship sails from port P for 8 km on a bearing of 070° to a buoy Q, then 6 km on a bearing of 160° to a lighthouse R. Calculate the distance PR and the bearing of R from P.
1
Find the angle inside the triangle at
Q. Start with the back bearing of P from
Q.
70 + 180 = 250°
2
Both directions at Q are now
measured from the same north line, so subtract.
angle PQR = 250 − 160 = 90°
3
A right angle, so use Pythagoras for the
distance.
PR² = 8² + 6² = 64 + 36 = 100 PR = 10 km
4
For the bearing, first find angle
QPR using tan (opposite 6, adjacent 8).
tan(QPR) = 6 ÷ 8 = 0.75 QPR = 36.87°
5
R is further clockwise from
north at P than Q is, so add.
bearing of R from P = 70 + 36.87 = 106.87°
PR = 10 km on a bearing of 106.9° (3 s.f.)
Exam tip Give bearings to 1 decimal place or to the nearest degree only if the
question says so — otherwise the usual 3 significant figures rule applies, so
106.9° is safe here. Keep the full value in your calculator until the very last
line; rounding 36.87° to 37° early can shift the final
answer.
Your turn
Practice set
Write as three-figure bearings: (a) south-west (b) a turn of 8° clockwise from north
(c) due north.
Find the back bearing of (a) 073° (b) 310°
(c) 180°.
The bearing of X from Y is 148°.
Find the bearing of Y from X.
From A the bearing of B is 035°
and the bearing of C is 290°. Find angle
BAC.
A boat sails 12 km due east, then 5 km due south. Calculate its distance and bearing from the start.
B is 8 km from A on a bearing of
140°. C is 6 km from B on a
bearing of 210°. Calculate AC and the bearing of
C from A.
Going clockwise from B to C is
290 − 35 = 255°, so the angle inside is
360 − 255 = 105°
Right angle between the legs: d = √(12² + 5²) = √169 =
13 km. tanθ = 5 ÷ 12 so
θ = 22.6° south of east, giving bearing
90 + 22.6 = 112.6°
Bearing of A from B is
140 + 180 = 320°, so angle ABC = 320 − 210 = 110°.
Cosine rule: AC² = 8² + 6² − 2(8)(6)cos110° = 132.8, so
AC = 11.5 km. Sine rule:
sin(BAC) = 6 sin110° ÷ 11.525 = 0.4892 so
angle BAC = 29.3°, and the bearing is
140 + 29.3 = 169.3°
Key points to remember
A bearing is measured from north, clockwise, and written with three figures:
045°, 008°, 237°.
“The bearing of B from A” puts the north line at A. Reversing the letters
gives a different angle.
Learn the compass values: N 000°, NE 045°,
E 090°, SE 135°, S 180°,
SW 225°, W 270°, NW 315°.
To draw a bearing over 180°, measure
360° − bearinganticlockwise from north.
Back bearing: add 180° if the bearing is under
180°, subtract 180° if it is
180° or more. The answer must stay between
000° and 360°.
The rule works because north lines are parallel, so the two angles at the ends of the journey
are co-interior angles and add to 180°. Quote that fact when a reason
is asked for.
Two bearings taken from the same point subtract to give the angle between the directions.
On a scale drawing, write the scale down and draw a fresh north line at every point before
measuring the next bearing.
When a question says calculate, find the triangle's angles from the bearings first, then use
Pythagoras and SOHCAHTOA for right angles, or the sine and cosine rules otherwise.